注册 登录
美国中文网首页 博客首页 美食专栏

obd2shop的个人空间 //www.sinovision.net/?651938 [收藏] [复制] [分享] [RSS]

x

博客栏目停服公告

因网站改版更新,从9月1日零时起美国中文网将不再保留博客栏目,请各位博主自行做好备份,由此带来的不便我们深感歉意,同时欢迎 广大网友入驻新平台!

美国中文网

2024.8.8

分享到微信朋友圈 ×
打开微信,点击底部的“发现”,
使用“扫一扫”即可将网页分享至朋友圈。

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial

已有 105 次阅读2024-6-13 03:51 | condor-xc002-pro, condor-xc002-pro 分享到微信

Today we'll discuss cutting a HON66 key with Xhorse Condor XC-002 PRO. Before cutting, always make sure the key-cutting machine is well-calibrated.

Height Level Adjustment
Method 1.
1)To start, we insert the original key with the help of a guiding block. We're gonna use a shim to make sure the key is well aligned.
2)Insert the key blank to the right. Now we're ready to begin height level adjustment.
3)Press down the main handle and check the indicator light. So we should just follow the direction of the light and rotate the micro-adjust knob until the middle light turns green.

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-1

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-2

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-3

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-4

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-5

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-6

Method2.
If you don't have a shim momentarily, there is another method you can apply.
1)To ensure accuracy, we can also use probes of the same specification on both sides.
2)Press down the main handle and rotate it to lock it. And you can utilize the probe and cutter of the machine for key alignment.
3)Replace the cutter and adjust the micro-adjust knob until the middle light turns green.
Okay, now we've finished the height level adjustment of Condor XC-002 PRO.

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-7

Preparation
Before we start cutting, we need to take a look at the clamp. There are 3 marked positions at the bottom of the clamp: A, B, and C.
1. Slide in the clamp and make one triangle directs to the line depending on your need.
2. Then turn on the power switch of the cutter and adjust the speed control knob to a suitable speed.

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-8

Key Cutting

After getting everything ready, now we can start duplicating the key.
1. Press down the main handle and start cutting.
Now we've finished the one side of the key.
2. Turn off the power switch of the cutter. Clean up the clamp and flip the key.
3. Similarly, align the key and finish the height level adjustment of the other side.
4. Then turn on the switch to cut the key.

*Do not forget to turn off the power when completed.

Now we've finished the cutting and have a new HON66 key.

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-9

Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial_图1-10

www.obd2shop.co.uk


免责声明:本文中使用的图片均由博主自行发布,与本网无关,如有侵权,请联系博主进行删除。







鲜花

握手

雷人

路过

鸡蛋

评论 (0 个评论)

facelist

您需要登录后才可以评论 登录 | 注册

 留言请遵守道德与有关法律,请勿发表与本文章无关的内容(包括告状信、上访信、广告等)。
 所有留言均为网友自行发布,仅代表网友个人意见,不代表本网观点。

关于我们| 反馈意见 | 联系我们| 招聘信息| 返回手机版| 美国中文网

©2024  美国中文网 Sinovision,Inc.  All Rights Reserved. TOP

回顶部