切换至摄影模板
博文
Perkins 2806F Engine Combustion Head Removal Procedure Guide
|
This article introduces the Perkins 2806F engine combustion head removal procedure
a. Remove the Exhaust Elbow.
WARNING
Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.
Perkins Engine ECM ECU Flash Files Collection Download
NOTICE:
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
WARNING
Hot engine components can cause injury from burns. Before performing maintenance on the en- gine, allow the engine and the components to cool.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF
Start By:
a. Remove the Exhaust Elbow.
WARNING
Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.
Perkins Engine ECM ECU Flash Files Collection Download
NOTICE:
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
WARNING
Hot engine components can cause injury from burns. Before performing maintenance on the en- gine, allow the engine and the components to cool.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF
Start By:
2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service
3. Loosen hose clamp (1) on hose assembly (2).
4. Remove bolts (4) and remove tube assembly (3).
Remove gasket (5) (not shown).
3. Loosen hose clamp (1) on hose assembly (2).
4. Remove bolts (4) and remove tube assembly (3).
Remove gasket (5) (not shown).
5. Disconnect hose assembly (6), hose assembly (7), hose assembly (10), and tube assembly (9). Cap the adapters and plug the hose assemblies.
6. Remove bolt (13) from ground strap (14) .
7. Disconnect high tension lead (8) from the sparkplug. Position the high tension lead away from the combustion head.
8. Remove flame detection temperature sensor (11)
Assembly, Temperature Sensor (DPF Inlet, Flame Detect) -Remove and Install for the correct and flame detect (12). Refer toDisassembly and procedure.
9.
Remove Aftertreatment Regeneration DeviceRefer to Disassembly and
Assembly, ARD Spark Plug-Remove and Install for the correct procedure.
(ARD) spark plug (15) from combustion head (21).
10. Remove nuts (16) from combustion head (21 ).
Remove the combustion head.
11. Remove gasket (20), tube assembly (19), and gasket (17).
12. If necessary, remove studs (18).
Perkins EST Diagnostic Adapter-High Quality
13. If necessary, follow Step 13.a through Step 13.d to disassemble combustion head (21).a. Install combustion head (21) into a suitable support.
b. Remove adapter (22) and adapter (23) from combustion head (21).
c. Remove adapter (24) and adapter (26) from combustion head (21).
d. Remove O-ring seal (25) (not shown) and O-
ring seal (27) (not shown) .
免责声明：本文中使用的图片均由博主自行发布，与本网无关，如有侵权，请联系博主进行删除。
上一篇:
Perkins 2806F Engine Combustion Head Installation Procedure Guide
下一篇: DL300-3/DL350-3 Wheel Loader Cylinder Head Removal and Installation Instructions
下一篇: DL300-3/DL350-3 Wheel Loader Cylinder Head Removal and Installation Instructions
全部作者的其他最新博文
- • the hydraulic release of the single hydraulic circuit of the caterpillar311D LRR
- • JCB Backhoe Loader Power Shift - Chain Adjustment
- • Perkins 2806F Engine Inlet and Exhaust Valve Springs - Remove and Install
- • Caterpillar 312D2 and 313D2 Excavator 3054C Engine System Pressure- -Release
- • Parking Brake Lining Clearance and Lever Travel Adjustment on Isuzu Vehicles
- • Doosan DA30 Dump Truck the ECU Wiring Tier2 -Removal
