博文
Perkins 2806F Engine Solenoid Valve (DEF Heater Coolant)-Remove and Install Guid
||
This article introduces Perkins 2806F Engine Solenoid Valve (DEF Heater Coolant)-Remove and Install
Removal Procedure：
NOTICE Care must be taken to ensure that fluids are con- tained
during performance of inspection, mainte-
nance, testing, adjusting and repair of the product.
Be prepared to collect the fluid with suitable contain-
ers before opening any compartment or disasslem-
bling any component containing fluids.
Dispose of all fluids according to local regulations and mandates.
NOTICE：
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the battery disconnect switch to the OFF position.
2.
Drain the coolant from the cooling system into a suitable container for
storage or disposal. Refer to Operation and Maintenance Manual,
"Cooling System Coolant -Change"for the correct procedure.
Perkins Engine ECM ECU Flash Files Collection Download
3. Disconnect harness assembly (1) from solenoid valve (2).
4. Loosen clamp hoses (6). Disconnect hose assembly (5) from solenoid valve (2).
5. Loosen clamp hoses (3). Disconnect hose assembly ( 4) from solenoid valve (2).
6. Remove bolts (7) and remove solenoid valve (2) from bracket (9).
Note: Note the orientation of the solenoid valve.
7. If necessary, follow Step 2. bthrough Step 7.b in order to remove bracket (9).
a. Remove bolts (8) from bracket (9).
b. Remove bracket (9) from the Diesel Emission Fluid (DEF) tank assembly.
Installation Procedure
Care
must be taken to ensure that fluids are con- tained during performance
of inspection, mainte- nance, testing, adjusting and repair of the
product. Be prepared to collect the fluid with suitable contain- ers
before opening any compartment or disassem- bling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components are clean and free
from wear and damage. If necessary, replace any components that are worn or damaged.
Typical example
2. If necessary, follow Step 2.a through Step 2.b in order to install bracket (9).
a. Position bracket (9) onto the DEF tank assembly.
b. Install bolts to bracket (9). Tighten the bolts to a torque of 9 N·m (80 lb in).
3. Position solenoid valve (2) to bracket (9). Ensure that the valve is correctly orientated.
4. Install bolts (4) to solenoid valve (2 ). Tighten the bolts to a torque of 9 N·m (80 lb in).
5. Connect hose assembly (5) to solenoid valve (2). Securely clamp hoses (6).
6. Connect hose assembly (4) to solenoid valve (2). Securely clamp hoses (3).
7. Connect harness assembly (1) to solenoid valve
8. Fill the cooling system with coolant. Refer to
Operation and Maintenance Manual, “Cooling
System Coolant - Change” for the correct
procedure.
9. Turn the battery disconnect switch to the ON
Perkins EST Diagnostic Adapter-High Quality
position.
免责声明：本文中使用的图片均由博主自行发布，与本网无关，如有侵权，请联系博主进行删除。
下一篇: How to replace Replacing 3516B and 3516B High Displacement Engines ECM
全部作者的其他最新博文
- • the hydraulic release of the single hydraulic circuit of the caterpillar311D LRR
- • JCB Backhoe Loader Power Shift - Chain Adjustment
- • Perkins 2806F Engine Inlet and Exhaust Valve Springs - Remove and Install
- • Caterpillar 312D2 and 313D2 Excavator 3054C Engine System Pressure- -Release
- • Parking Brake Lining Clearance and Lever Travel Adjustment on Isuzu Vehicles
- • Doosan DA30 Dump Truck the ECU Wiring Tier2 -Removal
