博文

How to Remove the Isuzu Excavator Fuel Injector

已有 230 次阅读2024-1-30 04:51 |系统分类:科技教育分享到微信

This article explains how to remove the Isuzu excavator fuel injector

ISUZU IDSS MX2-T Diagnostic Adapter System Support G-IDSS/US-IDSS/E-IDSS（Included DHL Shipping ）

The fuel injector is explained here taking the removal and installation of the No. 1 fuel injector as an example. The same steps can be used for the fuel injectors of other cylinders. Special care is required when handling fuel injectors. The tip of the nozzle is particularly delicate, and bumping the nozzle or wiping it with a grease rag can cause the hole to become clogged. Moreover, the injector wiring harness uses a high-voltage wiring harness, so the battery terminals must be removed before work. The removed high-pressure pipelines, seals and gaskets cannot be reused and must be replaced with new ones. ① Use a wrench (17 mm) to remove the bolt (1 in Figure 4-55), and then remove the battery negative terminal cable (2 in Figure 4-55). NOTE: When removing the terminals and wiring harness, keep them in a safe place to avoid mutual interference and open flames. Also, cover with a rubber cap to prevent sparks from entering.

② Use a wrench (12 mm) to remove the bolt (3 in Figure 4-56), and then remove the dipstick pipe (4 in Figure 4-56). NOTE: Cover lines with caps and cocks to prevent water, dust or dirt from entering. Clean lines with a spray of parts cleaner to prevent scratches and remove accumulated dust from fittings.
③ Use clamps to loosen the hose tie, and then remove the bypass hose (5 in Figure 4-57). NOTE: Cover hoses and lines with caps and stopcocks to prevent water, dust, or dirt from entering.

Isuzu G-IDSS Diagnostic Service System 06.2023 Download and Installation Service

④ Use a wrench (12 mm) to remove the bolts (6 in Figure 4-58) on the hose clamp (7 in Figure 4-58). ⑤ Use a wrench (12mm) to remove the 9 bolts (8 in Figure 4-59) and 2 nuts (9 in Figure 4-59) on the cylinder head cover (10 in Figure 4-59), and then remove the cylinder head cover.

⑥ Remove the connector (11 in Figure 4-60).

⑦Use a wrench (7mm) to remove the 2 nuts at each terminal position of the 4 injectors (13 in Figure 4-61)

11.2023 ISUZU US-IDSS Diagnostic Service II Truck Diagnostic System Download and Installation

⑧ Use a wrench (14mm) to loosen the 3 bolts (No. 12 in Figure 4-61), and then remove the wiring harness bracket (No. 14 in Figure 4-61) NOTE: When removing the nuts, loosen them the same amount each time so that all nuts are removed at the same time.

⑨ Use a wrench (12mm, 17mm) to remove 5 bolts (15 and 16 in Figure 4-62) and 5 washers (17 and 18 in Figure 4-62), and then remove the nozzle oil outlet pipe (Figure 4-62 19).

⑩ Use a wrench (10mm) to remove the bolts (20 in Figure 4-63) on the pipe clamp (23 in Figure 4-63). 0 Use a wrench (17 mm) to remove the sleeve nut (21 in Figure 4-63) on the pipe on the side of the injector. @Use a wrench (19 mm) to remove the sleeve nut (22 in Figure 4-63) on the common rail side pipe. NOTE: Cover lines with caps and cocks to prevent water, dust or dirt from entering. Clean lines with a spray of parts cleaner to prevent scratches and remove accumulated dust from fittings.

@Use a "TORX" Torx wrench (T40) to remove the bolts (24 in Figure 4-64) on the injector clamp (26 in Figure 4-64). @Remove the fuel injector (25 in Figure 4-64). 0 If it is difficult to remove the fuel injector (29 in Figure 4-65), use the fuel injector removal tool (28 in Figure 4-65). Install the fuel injector removal tool on the fuel injection pipe connection part, connect the slide hammer (27 in Figure 4-65) at the same time, and then remove the fuel injector.