博文

Perkins Indup Strial Diesel Engine Exhaust Fluid Module Disassemble Guide

已有 1258 次阅读2023-3-27 20:05 |系统分类:科技教育分享到微信

Perkins 2806F-E18TA Indup Strial Diesel Engine Exhaust Fluid Module Disassemble Guide

Perkins SPI2 Version 2018A Service & Parts Catalogue Software

Diesel Exhaust Fluid Module -
Assemble
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are con tained during performance of inspection, mainte nance, testing, adjusting and repair of the product.
Be prepared to collect the fluid with suitable contain ers before opening any compartment or disassem bling any component containing fluids.
Dispose of all fluids according to local regulations
and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened
component life
1. Ensure that all components are clean and free
from wear and damage. If necessary, replace any
components that are worn or damaged

2. If necessary, install filler cap (14) onto tank (16).
On some application the filler cap may be of a
different type. Refer to Original Equipment
Manufacturer (OEM) for the correct removal
procedure.
3. Position bracket (11) onto tank (16).
4. Install bolts (15) onto bracket (11). Tighten the
bolts to a torque of 4 N·m (35 lb in).

Perkins EST Electronic Service Tool Diagnostic Software Full Function 2022a
5. Position bracket (12) onto bracket (11).
6. Install bolts (13) to bracket (12). Tighten the bolts to a torque of 4 Nm (35 Ib in).

7. Install diesel exhaust fluid pump (10). Refer to Disassembly and Assembly, "Diesel Exhaust Fluid Pump -Remove and Install"for the correct procedure.
8. Position harness assembly (9) onto the bracket.
9. Install new cable straps (7) and new cable straps
(8) from harness assembly (9). Ensure that all the cable straps are installed in the original position.
Note: Ensure that the cable straps meet the OEM specifications.

10. Position relay (3) onto the bracket. Install bolt (1)
to the relay. Tighten the bolt to a torque of 4 Nm
(35 lb in).
11. Position relay (4) onto the bracket. Install bolt (2)
to the relay. Tighten the bolt to a torque of 4 Nm
(35 lb in).
12. Connect harness assembly (6) to relay (4).13. Connect harness assembly (5) to relay (3).
14. Turn the battery disconnect switch to the ON position.
End By: a. Install the voltage load protection module.
Refer to Disassembly and Assembly, "Voltage Load Protection Module -Remove and Install"
for the correct procedure.
b. Install the electronic control (Diesel Exhaust Fluid). Refer to Disassembly and Assembly,
"Electronic Control (Diesel Exhaust Fluid) -
Remove and Install"for the correct procedure.c. Install the manifold (DEF heater). Refer to Disassembly and Assembly, "Manifold (DEF Heater)-Remove and Install"for the correct procedure.
d. Install the solenoid valve (DEF heater coolant).
Refer to Disassembly and Assembly,
"Solenoid Valve (DEF Heater Coolant)-
Remove and Install"for the correct procedure.
e. Install the diesel exhaust fluid lines. Refer to Disassembly and Assembly, "Diesel Exhaust Fluid Lines-Remove and Install"for the correct procedure.
Perkins Engine ECM ECU Flash Files Collection Download

免责声明：本文中使用的图片均由博主自行发布，与本网无关，如有侵权，请联系博主进行删除。

上一篇: Hur man gör en JCB Grävlastare Power Side Shift Kedjejustering
下一篇: Introduce how to disassemble and inspect Yanmar marine engine fuel injection pum