切换至摄影模板
博文
DooSan Diesel Engline D18NAP Injector Disassembly Guide
This article mainly introduces DooSan Diesel Engline D18NAP Injector Disassembly
1. Remove the breather hose
Doosan Daewoo Excavator Operation and Repair Manual PDF
CAUTION
Do not reuse the clamps but replace with new ones.
2. Remove the common rail and the injection pipes
1) Loosen 3 hex nuts (D) and remove 3 washers (C).
2) Remove the electric connector (B) and 3 glow
plugs (A).
4. Remove the fuel return hose
1) Loosen the flange hex bolts (C).
2) Remove the hose clips and disconnect the fuel
hose (A)
5. Remove the right and left cylinder head cover.
Doosan DMS-5 (Doosan Data Monitoring System) Diagnostic Software V1.6.3
1) Loosen 8 flange hex bolts (D).
2) Remove the right cylinder head cover (C).
3) Loosen 10 flange hex bolts (B).
4) Remove the left cylinder head cover (A).
6. Remove the injectors
1) Loosen 3 hex bolts (D).
2) Remove 3 injector fixtures (C).
3) Remove 4 injectors (B).
4) Remove 3 injector seal ring washers (D)
CAUTION
• Do not reuse the head cover rubber seal and
the injector oil seal but replace with new
ones.
• Be careful not to damage the injector oil seal
of the cylinder head cover.
• Remove it by turning the injector slowly from
left to right
1. Remove the breather hose
Doosan Daewoo Excavator Operation and Repair Manual PDF
CAUTION
Do not reuse the clamps but replace with new ones.
2. Remove the common rail and the injection pipes
1) Loosen the fixing bolt (E).
2) Loosen the nuts of the fuel injection pipes.
3) Remove 4 fuel injection pipes (C) and (D)
CAUTION
Do not reuse fuel injection pipes; replace them
with new ones. If fuel injection pipes are reused
it may allow foreign substances into the fuel
pipes or cause oil leaks from bolt clamping and
cause a critical fault in engine performance.
4) Loosen 2 collared hex bolts (B) of the common rail.
5) Remove the common rail (A) from the intake
manifold.
3. Remove the glow plug.
1) Loosen 3 hex nuts (D) and remove 3 washers (C).
2) Remove the electric connector (B) and 3 glow
plugs (A).
4. Remove the fuel return hose
1) Loosen the flange hex bolts (C).
2) Remove the hose clips and disconnect the fuel
hose (A)
5. Remove the right and left cylinder head cover.
Doosan DMS-5 (Doosan Data Monitoring System) Diagnostic Software V1.6.3
1) Loosen 8 flange hex bolts (D).
2) Remove the right cylinder head cover (C).
3) Loosen 10 flange hex bolts (B).
4) Remove the left cylinder head cover (A).
6. Remove the injectors
1) Loosen 3 hex bolts (D).
2) Remove 3 injector fixtures (C).
3) Remove 4 injectors (B).
4) Remove 3 injector seal ring washers (D)
CAUTION
• Do not reuse the head cover rubber seal and
the injector oil seal but replace with new
ones.
• Be careful not to damage the injector oil seal
of the cylinder head cover.
• Remove it by turning the injector slowly from
left to right
免责声明：本文中使用的图片均由博主自行发布，与本网无关，如有侵权，请联系博主进行删除。
上一篇:
Cummins Fire Pump Drive Engines Belt Guard Removal/lnstallation Guide
下一篇: Isuzu Control Lever Assembly,Control Cable and Associated Parts Removal and In
下一篇: Isuzu Control Lever Assembly,Control Cable and Associated Parts Removal and In
全部作者的其他最新博文
- • the hydraulic release of the single hydraulic circuit of the caterpillar311D LRR
- • JCB Backhoe Loader Power Shift - Chain Adjustment
- • Perkins 2806F Engine Inlet and Exhaust Valve Springs - Remove and Install
- • Caterpillar 312D2 and 313D2 Excavator 3054C Engine System Pressure- -Release
- • Parking Brake Lining Clearance and Lever Travel Adjustment on Isuzu Vehicles
- • Doosan DA30 Dump Truck the ECU Wiring Tier2 -Removal
