博客栏目停服公告
因网站改版更新,从9月1日零时起美国中文网将不再保留博客栏目,请各位博主自行做好备份,由此带来的不便我们深感歉意,同时欢迎 广大网友入驻新平台!
美国中文网
2024.8.8
Which Audi TCM can be cloned with OBDSTAR DC706 ECU programmer on bench?
Currently, DC706 with TCM V30.01 can read and write EEPROM &Flash on Audi TEMIC DQ200, DQ250, DL501, VL381, DL382 and DQ400E. Some TCMs also can recalibrate mileage. Check the details below.
Brand | ECU Brand | Type | Dump | Comm. Mode |
AUDI | TEMIC | DQ200(0AM/0CW) DQ200Dxx | TC1766 | BENCH |
AUDI | TEMIC | DQ200(0AM/0CW) DQ200-MQB | TC1766 | BENCH |
AUDI | TEMIC | DQ250(02E/0D9) | TC1766 | BENCH |
AUDI | TEMIC | DL501(0B5) DL501Gen1 | TC1766 | BENCH |
AUDI | TEMIC | VL381(0AW) | TC1766 | BENCH |
AUDI | TEMIC | DQ200 G2 | TC1784 | BENCH |
AUDI | TEMIC | DL382 | TC1784 | BENCH |
AUDI | TEMIC | DQ200 G2-PQ | TC1784 | BENCH |
AUDI | TEMIC | DQ400E | TC1784 | BENCH |
Here are two test reports on Audi DQ200 and DQ400E.
1.OBDSTAR DC706 R/W EEPROM Flash and Recalibrate ODO on AUDI DQ200 G2 PQ TCM on BENCH
2.OBDSTAR DC706 R/W EEPROM Flash on AUDI DQ400E TCM on BENCH
Operation guide:
OBDSTAR DC706 host
OBDSTAR P004 adapter and jumper
ECU Bench Jumper
Main cable
AUDI DQ200 G2 PQ/ DQ400E TCM
Keep OBDSTAR DC706 charging and communication through the process
Turn on OBDSTAR DC706 ECU programmer
Select ECU Flasher>> All>> TCM>> TCM V30.01>> AUDI>> AUDI TEMIC DQ200 G2 PQ TC1784 (BENCH) or AUDI TEMIC DQ400E TC1784 (BENCH)
Click “PINOUT” to check the related wiring diagram and follow it to connect the DC706 and TCM correctly
Supply the 12V power to DC706 tablet
After connection, click “Start” to enter the operation interface
Audi DQ200 G2 PQ connection:
AUDI DQ400E connection:
Click “Connect” to make the service connect to the ECU successfully
Read and backup INT/EXT EEPROM and INT flash data in sequence
Audi DQ200 G2 PQ:
AUDI DQ400E (all are read successfully, here just show INT flash reading):
Select the corresponding INT/EXT EEPROM and INT flash file to write into new TCM
When the system prompts “whether to write HEX editor data?”, just click “No”.
Audi DQ200 G2 PQ:
AUDI DQ400E (all are read successfully, here just show INT flash writing):
DQ200 also supports odometer correction function, so select “Recalibrate ODO” to enter the new mileage (km/mile) and wait the process is done.
Finally, click “Disconnect” to disconnect TCM and exit the job.
All right! It’s easy and fast to clone Audi TEMIC TCM successfully with OBDSTAR DC706 ECU Chip Tuning Tool via bench mode.