切换至摄影模板
博文
SVCI J2534 Software Installation Error Solution
||
If you got trouble in using SVCI J2534 diagnostic interface, try to find the solution from this article.
Problem 1: When you open FVDI J2534 for ford software after installation, an error window pops out as shown in the picture below.
Eobdtool.co.uk engineer solution:
Don’t worry! The error above means you have not connected the SVCI J2534 device with your computer. Just connect your FVDI J2534 with computer, and the software will be opened normally.
Problem 2: When you put SVCI J2534 diagnostic interface to connect the computer and open the software, an IDSLoader error message appears on the screen “VCI not plugged into the car, or car battery voltage under 8 Volt.” as below.
Eobdtool.co.uk engineer solution:
For this error, it means you do not connect the vehicle ECU module and the ECU voltage may be less than 8 volts. Please use the OBD interface of SVCI J2534 to connect the ECU, and the software can be opened normally and run directly.
Note: Please don’t open the IDS software on the desktop directly, it is recommended to delete the IDS software shortcut on the desktop.
Problem 3: When connecting SVCI J2534 to vehicle and launching the Ford IDS software, an error returned says “Load IDS software failed. TDSNet setup error, Please reinstall IDS software.” This is on Windows 10 with version 113.0 IDS that came on the provided CD with the device.
Eobdtool.co.uk engineer solution:
Please change the laptop system, install the latest IDS software, then install start software.
To be updating…
Tech support: www.eobdtool.co.uk/
Article source：http://blog.eobdtool.co.uk/svci-j2534-software-installation-error-solution/
Problem 1: When you open FVDI J2534 for ford software after installation, an error window pops out as shown in the picture below.
Eobdtool.co.uk engineer solution:
Don’t worry! The error above means you have not connected the SVCI J2534 device with your computer. Just connect your FVDI J2534 with computer, and the software will be opened normally.
Problem 2: When you put SVCI J2534 diagnostic interface to connect the computer and open the software, an IDSLoader error message appears on the screen “VCI not plugged into the car, or car battery voltage under 8 Volt.” as below.
Eobdtool.co.uk engineer solution:
For this error, it means you do not connect the vehicle ECU module and the ECU voltage may be less than 8 volts. Please use the OBD interface of SVCI J2534 to connect the ECU, and the software can be opened normally and run directly.
Note: Please don’t open the IDS software on the desktop directly, it is recommended to delete the IDS software shortcut on the desktop.
Problem 3: When connecting SVCI J2534 to vehicle and launching the Ford IDS software, an error returned says “Load IDS software failed. TDSNet setup error, Please reinstall IDS software.” This is on Windows 10 with version 113.0 IDS that came on the provided CD with the device.
Eobdtool.co.uk engineer solution:
Please change the laptop system, install the latest IDS software, then install start software.
To be updating…
Tech support: www.eobdtool.co.uk/
Article source：http://blog.eobdtool.co.uk/svci-j2534-software-installation-error-solution/
免责声明：本文中使用的图片均由博主自行发布，与本网无关，如有侵权，请联系博主进行删除。
上一篇:
03.2020 MB SD Connect C4 Software Problems and Solutions
下一篇: SVCI J2534 Software Install& Update, Language, Vehicle Coverage FAQs
下一篇: SVCI J2534 Software Install& Update, Language, Vehicle Coverage FAQs
全部作者的其他最新博文
- • Autel Black Friday Sale: Auto 10% OFF
- • Formulaflash BMW ISN/VIN Modification by One-Click Support List
- • How to Active and Change Language on LAUNCH CRP919 EV Diagnostic Tool?
- • Lonsdor K518 Pro MAHINDRA Auto IMMO Update
- • OBDSTAR MT203 CAN Driver/Gateway Simulator Register and Update Guide
- • Lonsdor K518 Newly Release LT30-01 TOYOTA 4A Universal Smart Key
